- Products
-
Projects
- Lofted Bed
- Kitchen Storage Shelf
- Closet System
- Patio Chair
- Patio Table
- Dolly
- Projector Screen
- Sign Frame
- Patio Frame
- Bird House
- Horse Shoes
- Dog Bowl
- Hanging Shelf
- Decorative Shelf
- Sofa Table
- Entryway Shoe Rack
- Stair Railing
- Bicycle Exercise Stand
- Coding Table
- Train Table
- Buffet Table
- Target Range
- Candle Holder
- Decorative Bench
- Outside Bench
- Napkin Holder
- Step Stool
- Fence Wood Rack
- Accessory Holder
- Plant Hanger
- Mail Slot Table
- Coffee Cart
- Bench
- Kitchen Island Rack
- Full Bed
- Gym Hooks
- TV Console
- Bar Top
- Wall Mounted Barbell Rack
- Swivel Table
- Mailbox
- TV Stand
- Console Shelf
- Full Bed
- Towel and Toilet Paper Rack
- Garage Shelf
- Coat Rack
- Stool
- Garage Workbench
- Living Room Table
- Outdoor Railing
- Bookshelf
- Wall Shelf
- Small Shelf
- Entryway Coat Rack
- Decorative Serving Cart
- Serving Station
- Serving Cart
- Corner Desk
- Conference Room Table
- Side Table
- Hallway Table
- Lamp
- Lamps
- Coffee Table
- Decorative Coffee Table
- Worktable
- Blog
- About
- Contact
Products
Projects
Blog
About
Contact
TV Console
Need a space for your TV? Get the plans for your very own TV Console!
Skill Level
Estimated Cost
Estimated Time
Tools & Materials
SteelTek Supplies (3/4"):
- (10) Flange - (673-106HC)
- (2) 90 Degree Elbow - (672-406HC)
- (4) Three Socket Tee - (670-404HC)
- (2) End Plug - (678-404HC)
- (2) Coupling - (674-904HC)
- (2) 60" Non-Threaded Pipe
- (4) 28" Non-Threaded Pipe
- (2) 16" Non-Threaded Pipe
- (2) 14" Non-Threaded Pipe
- (2) 10" Non-Threaded Pipe
Other Supplies:
- (24) Wood Screws
- (1) Wood Top - 72" x 24"
- (1) Wood Shelf - 24" x 8.5"
Tools:
- (1) Allen Wrench - 6 Millimeters
- (1) Drill
- (1) Hammer
How To
Stage 1
Installing Flanges and Legs
- Start off by installing the Flanges (673-104HC) with wood screws. Line the Flanges up on the bottom of the board and mark you the Flange holes.
- Pre-drill marked holes and then install your Flanges using wood screws.
- Attach a 28” pipe to each corner Flange and a 14” pipe in the two middle Flanges then tighten set screws.
Steel•Tek Professional Tip
Base the length of the screws by the thickness of the wood piece being used.
Stage 2
Building Supports
- Take two 60” pipes and attach the middle of a Three Socket Tee (670-404HC) to each end. Make sure the vertical holes in the Three Socket Tee are not being blocked then tighten set screws.
- Take two 16” pipes and slide a Coupling (674-904HC) to the middle and tighten set screws.
- Attach the middle of a Three Socket Tee to each end of 16” pipe. Make sure the vertical holes in the Three Socket Tee are not being blocked then tighten set screws.
- Take two 10“ pipes and hammer in an End Plug (678-404HC) in only one side of each pipe.
- Attach an Elbow (672-504HC) to the open ends of 10” pipe then tighten set screws,
Stage 3
Attaching Supports
- Take the 10” pipe built in Stage 2 and attach open end of Elbow (672-504HC) to 14” vertical pipes then tighten set screws.
- Take the 16” pipe built in Stage 2 and slide one up the left legs and one up the right legs then tighten set screws. Adjust height to personal preference.
- Take the 60” pipe built in Stage 2 and slide one up the back legs and one up the front legs then tighten sets screws. Adjust height to personal preference.
Stage 4
Placing shelf and attaching floor flanges
- Attach a Flange (673-104HC) to the bottom of each leg then tighten set screws.
- Take the 24” x 8.5” wood piece and place it on the 10” horizontal pipes.
- For added security, add Offset Flanges (679-904HC) to the 10” shelf pipes and secure to shelf with wood screws.