- Products
-
Projects
- Train Table
- Buffet Table
- Target Range
- Candle Holder
- Decorative Bench
- Outside Bench
- Napkin Holder
- Step Stool
- Fence Wood Rack
- Accessory Holder
- Plant Hanger
- Mail Slot Table
- Coffee Cart
- Bench
- Kitchen Island Rack
- Full Bed
- Gym Hooks
- TV Console
- Bar Top
- Wall Mounted Barbell Rack
- Swivel Table
- Mailbox
- TV Stand
- Console Shelf
- Full Bed
- Towel and Toilet Paper Rack
- Garage Shelf
- Coat Rack
- Stool
- Garage Workbench
- Living Room Table
- Outdoor Railing
- Bookshelf
- Wall Shelf
- Small Shelf
- Entryway Coat Rack
- Decorative Serving Cart
- Serving Station
- Serving Cart
- Corner Desk
- Conference Room Table
- Side Table
- Hallway Table
- Lamp
- Lamps
- Coffee Table
- Decorative Coffee Table
- Worktable
- Blog
- About
- Contact
Products
Projects
Blog
About
Contact
Swivel Table
Practicle for small spaces and affordable design.
Skill Level
Estimated Cost
Estimated Time
Tools & Materials
SteelTek Supplies (3/4"):
- (11) Flange - (673-104HC)
- (6) Single Socket Tee - (670-104HC)
- (2) Side Outlet Tee - (671-604HC)
- (2) Directional Coupling Caster - (678-614)
- (1) Swivel Coupling Caster (678-514)
- (1) Coupling - (674-904HC)
- (1) 41" Non-Threaded Pipe
- (4) 29.5" Non-Threaded Pipe
- (1) 28.5" Non-Threaded Pipe
- (3) 24" Non-Threaded Pipe
- (1) 8.5" Non-Threaded Pipe
Other Supplies:
- 48" x 18" Wood Piece
- 36" x 15" Wood Piece
- 28 Wood Screws
Tools:
- Drill
- (1) Allen Wrench - 6 Millimeters
How To
Stage 1
Installing Flanges
- Start by attaching your Flanges (673-104HC) to your two wood pieces.
- Each Flange (673-104HC) should be 1” away from each wood piece side.
- Place Flanges (673-104HC) on the boards, mark the holes and then pre-drill your marks.
- Install Flanges using wood screws.
- Once Flanges (673-104HC) are installed, you will need to drill a 1.125” diameter hole on the smaller board.
- Place smaller board on top of bigger board for hole placement so the longer pipe from the bigger board can go through the hole.
Stage 2
Installing Legs
- The 24” pipe will go into the installed Flanges (673-104HC) on the smaller board and the 29.5” pipe will go into the installed Flanges (673-104HC) on the larger board.
- A 29.5” pipe will slide into the 1.125” diameter hole drilled in step one.
- Make sure the smaller board is level then secure it with a Coupling (674-904HC).
Stage 3
Building Brackets
- Take the 41” pipe and attach a Side Outlet Tee (671-604HC) to each side. Make sure the vertical holes are not blocked.
- Slide a 12” pipe into each open end of the Side Outlet Tees (671-604HC). Make sure the vertical holes are not blocked.
- Attach a Single Socket Tee (670-104HC) to each end of the 12” pipe.
- Take your 8.5” pipe and attach a Single Socket Tee (670-104HC) to each end.
- Take your 28.5” pipe and attach a Singe Socket Tee (670-104HC) to each end.
Stage 4
Installing Brackets
- Install braces made in Stage 3 according to the above diagram.
- The fittings attached to the 28.5” pipe will rest on top of the fittings attached to the 8.5” pipe.
- The fittings attached to the 41” pipe and the fittings attached to the 8.5” pipe should measure 14.25” from the floor.
Stage 5
Finish With Flanges and Casters
- Attach Flanges (673-104HC) to each outside 29.5” leg attached to the larger board.
- Attach Directional Coupling Casters (678-614) to the left legs of the smaller swivel board. Make sure the Directional Coupling Casters (678-614) are pointed in the direction of where the table will swivel.
- Attach Swivel Coupling Caster (678-514) to the right leg of the smaller swivel board.