- Products
-
Projects
- Moving Work Station
- Loft Bed Railing
- Cabinet
- Kitchen Island
- Lofted Bed Accessories
- Kitchen Storage Shelf
- Closet System
- Patio Chair
- Patio Table
- Dolly
- Projector Screen
- Sign Frame
- Patio Frame
- Bird House
- Horse Shoes
- Dog Bowl
- Hanging Shelf
- Decorative Shelf
- Sofa Table
- Entryway Shoe Rack
- Stair Railing
- Bicycle Exercise Stand
- Coding Table
- Train Table
- Buffet Table
- Target Range
- Candle Holder
- Decorative Bench
- Outside Bench
- Napkin Holder
- Step Stool
- Fence Wood Rack
- Accessory Holder
- Plant Hanger
- Mail Slot Table
- Coffee Cart
- Bench
- Kitchen Island Rack
- Full Bed
- Gym Hooks
- TV Console
- Bar Top
- Wall Mounted Barbell Rack
- Swivel Table
- Mailbox
- TV Stand
- Console Shelf
- Full Bed
- Towel and Toilet Paper Rack
- Garage Shelf
- Coat Rack
- Stool
- Garage Workbench
- Living Room Table
- Outdoor Railing
- Bookshelf
- Wall Shelf
- Small Shelf
- Entryway Coat Rack
- Decorative Serving Cart
- Serving Station
- Serving Cart
- Corner Desk
- Conference Room Table
- Side Table
- Hallway Table
- Lamp
- Lamps
- Coffee Table
- Decorative Coffee Table
- Worktable
- Blog
- About
- Contact
Products
Projects
Blog
About
Contact
Stool
Easily built stool, at a reasonable cost
Skill Level
Estimated Cost
Estimated Time
Tools & Materials
SteelTek Supplies (3/4"):
- (1) Flange (673-104HC)
- (1) Four Socket Cross (675-804HC)
- (4) Elbow (672-504HC)
- (5) End Plugs (678-404HC)
- (1) 18" Non-Threaded Pipe
- (4) 6" Non-Threaded Pipe
- (4) 4" Non-Threaded Pipe
Other Supplies:
- Wooden Seat
- Wood Screws
Tools:
- (1) Allen Wrench: - 6 Millimeters
- (1) Drill: for predrilling and securing SteelTek Flange to wood
How To
Stage 1
Installing Flange to Seat
- Take your wooden seat and place Flange (673-104HC) in the middle.
- Mark the Flange (673-104HC) holes and predrill marked holes.
- Take wood screws and attach a Flange (673-104HC) to the bottom of wooden seat.
Stage 2
Middle Base
- Take Ends Plug (678-404HC) and hammer into one side of 18” pipe.
- Slide Four Socket Cross (675-804HC) down onto pipe then slide open end of 18” pipe into Flange (673-104HC) and then and tighten set screws.
Steel•Tek Professional Tip
You will need to readjust Four Socket Cross (675-804HC) after legs are installed.
Stage 3
Installing Legs
- Slide 6” pipe into each horizontal hole of Four Socket Cross (675-804HC) and tighten set screws.
- Attach Elbow (672-504HC) to each open end of 6” pipe and tighten set screw. Make sure that the open end of Elbow is pointed towards the ground.
Stage 4
Closing Pipes
- Hammer End Plugs (678-404HC) into 4” pipe.
- Slide open ends of 4” pipe into open ends of Elbows (672-504HC) and tighten set screws.
Steel•Tek Professional Tip
You will need a hammer for this part and it might be a good idea to go ahead and hammer these in before you attach them to the Elbows.