- Products
-
Projects
- Lofted Bed
- Kitchen Storage Shelf
- Closet System
- Patio Chair
- Patio Table
- Dolly
- Projector Screen
- Sign Frame
- Patio Frame
- Bird House
- Horse Shoes
- Dog Bowl
- Hanging Shelf
- Decorative Shelf
- Sofa Table
- Entryway Shoe Rack
- Stair Railing
- Bicycle Exercise Stand
- Coding Table
- Train Table
- Buffet Table
- Target Range
- Candle Holder
- Decorative Bench
- Outside Bench
- Napkin Holder
- Step Stool
- Fence Wood Rack
- Accessory Holder
- Plant Hanger
- Mail Slot Table
- Coffee Cart
- Bench
- Kitchen Island Rack
- Full Bed
- Gym Hooks
- TV Console
- Bar Top
- Wall Mounted Barbell Rack
- Swivel Table
- Mailbox
- TV Stand
- Console Shelf
- Full Bed
- Towel and Toilet Paper Rack
- Garage Shelf
- Coat Rack
- Stool
- Garage Workbench
- Living Room Table
- Outdoor Railing
- Bookshelf
- Wall Shelf
- Small Shelf
- Entryway Coat Rack
- Decorative Serving Cart
- Serving Station
- Serving Cart
- Corner Desk
- Conference Room Table
- Side Table
- Hallway Table
- Lamp
- Lamps
- Coffee Table
- Decorative Coffee Table
- Worktable
- Blog
- About
- Contact
Products
Projects
Blog
About
Contact
Patio Chair
Grab some lemonade and relax outside on your new Patio Chair!
Skill Level
Estimated Cost
Estimated Time
Tools & Materials
SteelTek Supplies (3/4"):
- (8) Black Elbow - (682-504HC)
- (4) Black Single Socket Tee - (680-104HC)
- (7) Black 24" Non Threaded Pipe - (584-240PE30HC)
- (3) Black 18" Non Threaded Pipe - (584-180PE30HC)
Other Supplies:
- Wooden Seat
- Wood Screws
Tools:
- Allen Wrench - 6 Millimeter
- Drill
How To
Stage 1
Assembling Chair Front
- Slide a Single Socket Tee (680-104HC) onto two18” pipes, and tighten them at 7 inches from one end.
- Attach a 24” pipe in the open ends of the Single Socket Tees (680-104HC) attached to the 18” pipes then tighten set screw.
- Attach an Elbow (682-504HC) to each of the open ends of 18” pipe. Make sure the Elbows (682-504HC) are facing the same direction then tighten set screws.
Steel•Tek Professional Tip
- As you build the top, make sure all of the screws on your connectors are facing down or to the inside.
Stage 2
Assembling Arms and Legs
- Attach four 24” pipes to the open ends of the Elbows (682-504HC) then tighten set screws.
- Attach four Elbows (682-504HC) to the open end of each 24” pipe. Make sure the Elbows (682-504HC) are facing inward then tighten set screws.
Stage 3
Assembling Back Support
- Slide a Single Socket Tee (680-104HC) on a 24” pipe, center it then tighten set screws.
- Repeat the last step.
- Slide an 18” pipe into the open ends of the Single Socket Tees (680-104HC) and tighten set screws.
Stage 4
Attaching Back Support
- Install what was built in Stage 3 into open ends of available Elbows (682-504HC) then tighten set screws.
Stage 5
Attaching Seat
- This seat was installed by drilling holes into the pipe and installing using wood screws.
- You can also install this using Offset Flanges (689-904HC) and Double Tab Offset Flanges (689-804HC).
Stage 6
Finish
For Instructions on how to build the Wooden Seat follow the link