- Products
-
Projects
- Kitchen Island
- Lofted Bed
- Kitchen Storage Shelf
- Closet System
- Patio Chair
- Patio Table
- Dolly
- Projector Screen
- Sign Frame
- Patio Frame
- Bird House
- Horse Shoes
- Dog Bowl
- Hanging Shelf
- Decorative Shelf
- Sofa Table
- Entryway Shoe Rack
- Stair Railing
- Bicycle Exercise Stand
- Coding Table
- Train Table
- Buffet Table
- Target Range
- Candle Holder
- Decorative Bench
- Outside Bench
- Napkin Holder
- Step Stool
- Fence Wood Rack
- Accessory Holder
- Plant Hanger
- Mail Slot Table
- Coffee Cart
- Bench
- Kitchen Island Rack
- Full Bed
- Gym Hooks
- TV Console
- Bar Top
- Wall Mounted Barbell Rack
- Swivel Table
- Mailbox
- TV Stand
- Console Shelf
- Full Bed
- Towel and Toilet Paper Rack
- Garage Shelf
- Coat Rack
- Stool
- Garage Workbench
- Living Room Table
- Outdoor Railing
- Bookshelf
- Wall Shelf
- Small Shelf
- Entryway Coat Rack
- Decorative Serving Cart
- Serving Station
- Serving Cart
- Corner Desk
- Conference Room Table
- Side Table
- Hallway Table
- Lamp
- Lamps
- Coffee Table
- Decorative Coffee Table
- Worktable
- Blog
- About
- Contact
Products
Projects
Blog
About
Contact
Tools & Materials
SteelTek Supplies (1-1/4"):
- (2) 90° Elbow - (673-506HC)
- (5) Single Socket Tee - (670-106HC)
- (3) Flange - (673-106HC)
- (2) Two Socket Cross - (671-906HC)
- (1) 73.2" Non-Threaded Pipe
- (3) 39.6" Non-Threaded Pipe
- (4) 34.8" Non-Threaded Pipe
Other Supplies:
- (12) Concrete Screws
Tools:
- Allen Wrench
- Drill and Concrete Drill Bits
How To
Stage 1
Building Legs
- Start by taking the three 39.6" pipes and insert the bottom into Flanges then tighten set screw.
Outside Legs:
- Take two 39.6" pipes and slide two Single Socket Tees horizontally onto each pipe. Adjust to desired height and tighten set screws.
- Attach Elbow to top of the two outside legs and tighten set screw.
Inside Leg:
- Slide two, Two Socket Crosses onto one 39.6" pipe and set height according to the Single Socket Tees on the outside legs then tighten set screws.
- Attach Single Socket Tee to the top of the inside leg and tighten set screw.
Steel•Tek Professional Tip
- Remember not to slide the Single Socket Tee on the inside leg too far onto the 39.6" pipe as not to block the hole for the 73.2" top horizontal pipe.
- Make sure the the Two Socket Crosses and Single Socket Tee horizontal holes are all facing the same direction.
Stage 2
Attaching Horizontal Pipes and Leg to Ground
- Start by marking your Flange holes on the end leg and predrilling with a drill bit for the respective surface.
- Drill screws into Flange holes to secure outside leg.
- Slide 34.8" pipes into Single Socket Tees of outside leg and Two Socket Crosses of inside leg then tighten set screws.
- Mark Flange holes of inside leg, predrill marked holes then drill screws into flange holes to secure inside leg.
Steel•Tek Professional Tip
- Make sure you are using the correct drill bits and screws for the surface you are attching this too.
Stage 3
Attaching Top Rail
- Slide 73.2" pipe through Single Socket Tee of inside leg and into the Elbow of outside leg then tighten set screws.
Steel•Tek Professional Tip
- Again, make sure that the fittings holes are all going in the same direction.
Stage 4
Attaching Second Outside Leg
- Slide 34.8" pipes into Single Socket Tees of outside leg and Two Socket Crosses of inside leg while also sliding open end of 73.2" pipe into Eblow of outside leg.
- Mark Flange holes of outside leg, predrill marked holes then drill screws into flange holes to secure the second outside leg.
- Tighten set screws.
Steel•Tek Professional Tip
- Fittings are available to extend this railing in a 90° direction and even create railing for a stair case.