Organize your mail room with this Mail Slot Table!
Skill Level
Estimated Cost
Estimated Time
Tools & Materials
SteelTek Supplies (3/4"):
(4) Side Outlet Elbow - (672-804HC)
(4) Single Socket Tee - (670-404HC)
(6) Double Tab Offset Flange - (679-804HC)
(2) Side Outlet Tee - (671-604HC)
(4) Offset Flange - (679-904HC)
(4) Standard Railing Flange - (673-204HC)
(1) Hook - (678-204HC)
(4) 24" Non-Threaded Pipe
(4) 35" Non-Threaded Pipe
(4) 46" Non-Threaded Pipe
Other Supplies:
Wood Screws
60"x30" Top Wood Piece
48"x24" Bottom Wood Piece
Tools:
(1) Allen Wrench - 6 Millimeters
Drill
How To
Stage 1
Bottom Base
Start with 2 46” pipes and x2 24“ pipes.
Slide an Offset Flange (679-904HC) onto each pipe, center the Offset Flanges on the 46” pipe then tighten set screws.
Attach a Side Outlet Tee (671-604HC) to each end of 1 46“ pipe. Make sure the horizontal holes are facing the same direction and the vertical holes are not being blocked by the pipe.
Attach a 24” pipe to each horizontal open end of the Side Outlet Tees (671-604HC). Again, make sure the vertical holes are not being blocked by the 24” pipe.
Take the other 46” pipe and attach the bottom of a Single Socket Tee (670-104HC) on each end. Make sure the horizontal hole is not being blocked by the pipe.
Take the piece you just built and slide the open ends of each Single Socket Tee (670-104HC) onto the open ends of 24” pipe. Slide down this across the pipe about 4” and then tighten set screws.
Attach the bottom of Single Socket Tee (670-104HC) to each open end of 24” pipe. Make sure the vertical holes are not being blocked then tighten set screws.
Stage 2
Top Base
Take 3 24” pipes and slide x2 Double Tab Offset Flanges (679-804HC) on each pipe. Space them evenly then tighten set screws.
Attach a Single Socket Tee (670-104HC) to each end of one of the 24” pipes. Make sure the horizontal holes are not being blocked then tighten set screws.
Take 2 46in pipes and slide the Single Socket Tees (670-104HC) attached to the 24“ pipe on each 46” pipe. Center then tighten set screws.
Attach a Side Outlet Elbow (672-804HC) to each end of the 2 remaining 24“ pipes. Make sure the vertical holes are not being blocked then tighten set screws.
Now slide these 2 24” pipes with Side Outlet Elbows (672-804HC) onto the open horizontal ends of each 46” pipe. Make sure the vertical holes are not being blocked then tighten set screws.
Stage 3
Attaching Bottom and Top Bases
Take 4 35” pipes and attach a Standard Railing Flange(673-204HC) to one side of each pipe. Tighten set screws.
Take the piece built in Stage 1 and slide onto each 35” pipe. Set to desired height, level then tighten set screws.
Slide Hook (678-204HC) onto whatever leg you like. We placed it on the from left leg then tighten set screw.
Attach the piece built in Stage 2 to the top of each 35” pipe leg then tighten set screws.
Stage 4
Attaching Wood Top and Bottom
Place wood pieces on top of Offset Flanges (679-904HC) and Double Tab Offset Flanges (679-804HC), mark holes then pre-drill marked holes.
Attach the wood pieces using washers and wood screws.