- Products
-
Projects
- Decorative Shelf
- Sofa Table
- Entryway Shoe Rack
- Stair Railing
- Bicycle Exercise Stand
- Coding Table
- Train Table
- Buffet Table
- Target Range
- Candle Holder
- Decorative Bench
- Outside Bench
- Napkin Holder
- Step Stool
- Fence Wood Rack
- Accessory Holder
- Plant Hanger
- Mail Slot Table
- Coffee Cart
- Bench
- Kitchen Island Rack
- Full Bed
- Gym Hooks
- TV Console
- Bar Top
- Wall Mounted Barbell Rack
- Swivel Table
- Mailbox
- TV Stand
- Console Shelf
- Full Bed
- Towel and Toilet Paper Rack
- Garage Shelf
- Coat Rack
- Stool
- Garage Workbench
- Living Room Table
- Outdoor Railing
- Bookshelf
- Wall Shelf
- Small Shelf
- Entryway Coat Rack
- Decorative Serving Cart
- Serving Station
- Serving Cart
- Corner Desk
- Conference Room Table
- Side Table
- Hallway Table
- Lamp
- Lamps
- Coffee Table
- Decorative Coffee Table
- Worktable
- Blog
- About
- Contact
Products
Projects
Blog
About
Contact
Tools & Materials
SteelTek Supplies (3/4")::
- (8) Flange (673-104HC)
- (8) 90° Corner Swivel Combo (676-804HC)
- (4) Swivel Base (676-904HC)
- (2) Couling (674-904HC
- (2) 36" Non-Threaded Pipe
- (4) 14.5" Non-Threaded Pipe
- (6) 15" Non-Threaded Pipe
Other Supplies:
- (1) Wood Top: 27.75" x 49.5
- (24) Wood Screws
Tools:
- (1) Allen Wrench: - 6 Millimeters
- (1) Drill: for predrilling and securing SteelTek fittings to wood
How To
Stage 1
Installing Legs
- Place Flanges 4" from the edge at each corner of table top, then mark the flange holes and predrill the marked holes.
- Install Flanges with wood screws.
- Slide x4 15” pipes into each flange and tighten set screws.
Stage 2
Building Top Base
- Take the x4 90° Corner Swivel Combination (676-804HC) and place them in a rectangle shape.
- Attach x2 36” pipes into each end of 90° Corner Swivel Combination (676-804HC) parallel to each other as shown in picture and tighten set screws.
- Attach x2 15” pipes into the open ends of the 90° Corner Swivel Combination (676-804HC) parallel to each other as shown in picture and tighten set screws.
Stage 3
Installing Top Base
- Take the base built in Stage 2 and slide each leg through open vertical holes in the 90° Corner Swivel Combination (676-804HC).
- Make sure that the 90° Corner Swivel Combination (676-804HC) and the Flange (673-104HC) make contact and tighten set screws.
Stage 4
Building Bottom Base
- Slide coupling on 36” pipe for aesthetic and tighten set screws.
- Take your 36" pipe and attach a 90° Corner Swivel Combination (676-804HC) to each end and tighten set screws.
- Slide 14.5" pipe into open horizontal ends of 90° Corner Swivel Combination (676-804HC) and tighten set screws.
- Attach Swivel Base (676-904HC) to open ends of 14.5" pipe and tighten set screws.
- Repeat this process for the other side of the bottom base.
Stage 5
Installing Bottom Base
- This process will be easier if you flip the table upside down.
- Slide legs through vertical holes of the 90° Corner Swivel Combination (676-804HC) until Swivel Bases (676-904HC) are up against the bottom of the table top.
- One swivel base should be behind the 15” pipe and one should be in front of the 15” pipe and the same goes for the other side. See picture for reference.
- Mark Swivel Base (676-904HC) holes and predrill before installing.
- Install Swivel Bases (676-904HC) with wood screws then tighten set screws on 90° Corner Swivel Combination (676-804HC).
Stage 6
Attaching Flanges
- Slide each leg into Flanges (673-104HC) and tighten set screws.