- Products
-
Projects
- Dog Bowl
- Hanging Shelf
- Decorative Shelf
- Sofa Table
- Entryway Shoe Rack
- Stair Railing
- Bicycle Exercise Stand
- Coding Table
- Train Table
- Buffet Table
- Target Range
- Candle Holder
- Decorative Bench
- Outside Bench
- Napkin Holder
- Step Stool
- Fence Wood Rack
- Accessory Holder
- Plant Hanger
- Mail Slot Table
- Coffee Cart
- Bench
- Kitchen Island Rack
- Full Bed
- Gym Hooks
- TV Console
- Bar Top
- Wall Mounted Barbell Rack
- Swivel Table
- Mailbox
- TV Stand
- Console Shelf
- Full Bed
- Towel and Toilet Paper Rack
- Garage Shelf
- Coat Rack
- Stool
- Garage Workbench
- Living Room Table
- Outdoor Railing
- Bookshelf
- Wall Shelf
- Small Shelf
- Entryway Coat Rack
- Decorative Serving Cart
- Serving Station
- Serving Cart
- Corner Desk
- Conference Room Table
- Side Table
- Hallway Table
- Lamp
- Lamps
- Coffee Table
- Decorative Coffee Table
- Worktable
- Blog
- About
- Contact
Products
Projects
Blog
About
Contact
Lamp
Easy to make, this lamp will be perfect for when you need a bit of light. With the SteelTek fittings you can change how the arms sit to help light your room the way you want to.
Skill Level
Estimated Cost
Estimated Time
Tools & Materials
SteelTek Pieces Needed (3/4):
- (1) 3/4" Coupling - (674-904HC)
- (3) 3/4" 90 Degree Elbows - (672-504HC)
- (1) 3/4" Four Socket Cross - (679-804HC)
- (1) 3/4" Flange - (673-104HC)
- (1) 3/4" Plug - (678-404HC)
- (1) 3/4" x 36" Pipe
- (2) 3/4" x 4" Pipe
- (1) 3/4" x 3" Pipe
- (1) 3/4" x 2" Pipe
Other Materials:
- (24) 3/4" flat head screws, screw head must be #12 or higher
- (1) 8" wide x 6" long x 23" tall wood base. For this project have holes predrilled for wiring to be fed through. Apply finishing after all holes are drilled and your flange is positioned and has been predrilled.
Tools Needed:
- (1) Allen Wrench - 6 Millimeters
How To
Stage 1
Base Assembly
- Place the Flange above where you have pre-drilled to allow for wiring. Secure the Flange to the wood base.
- Attach the 36” length of pipe to the Flange and secure using the Allen Wrench.
- Place the Four Socket Cross at the top of the 36” pipe length. Slide it down so one bolt can secure the Cross and pipe together as more pipes will be used for the other outlets.
Stage 2
Arm Assembly
- Each 4” length of pipe should be placed on the two horizontal outlets of the Four Socket Cross. Slide them in so the bolt can secure the pipe but do not slide each length all the way through.
- For the top Cross outlet, slide in and secure the 3” length of pipe.
- The Coupling goes on top of the 3” pipe length, but only slide it so that the bottom bolt can be secured to the pipe. The top bolt will secure the electrical lighting socket.
Stage 3
Final Arm Assembly
- At the end of each 4” pipe length, add a 90 Degree Elbow. Point the left Elbow down, and the right Elbow up and firmly secure each using the Allen Wrench.
- For the left Elbow, attach the electrical lighting socket and secure it in place.
- On the right Elbow, slide the 2” length of pipe in and secure it.
- The final Elbow goes onto the top of the 2” pipe facing outwards. On the open end of this Elbow attach the final lighting socket and secure it in place.