- Products
-
Projects
- Sign Frame
- Patio Frame
- Bird House
- Horse Shoes
- Dog Bowl
- Hanging Shelf
- Decorative Shelf
- Sofa Table
- Entryway Shoe Rack
- Stair Railing
- Bicycle Exercise Stand
- Coding Table
- Train Table
- Buffet Table
- Target Range
- Candle Holder
- Decorative Bench
- Outside Bench
- Napkin Holder
- Step Stool
- Fence Wood Rack
- Accessory Holder
- Plant Hanger
- Mail Slot Table
- Coffee Cart
- Bench
- Kitchen Island Rack
- Full Bed
- Gym Hooks
- TV Console
- Bar Top
- Wall Mounted Barbell Rack
- Swivel Table
- Mailbox
- TV Stand
- Console Shelf
- Full Bed
- Towel and Toilet Paper Rack
- Garage Shelf
- Coat Rack
- Stool
- Garage Workbench
- Living Room Table
- Outdoor Railing
- Bookshelf
- Wall Shelf
- Small Shelf
- Entryway Coat Rack
- Decorative Serving Cart
- Serving Station
- Serving Cart
- Corner Desk
- Conference Room Table
- Side Table
- Hallway Table
- Lamp
- Lamps
- Coffee Table
- Decorative Coffee Table
- Worktable
- Blog
- About
- Contact
Products
Projects
Blog
About
Contact
Entryway Bench
Need a place to sit and take off your shoes when you get home? Build your own Entryway Bench!
Skill Level
Estimated Cost
Estimated Time
Tools & Materials
SteelTek Supplies (3/4"):
- (4) Black Flange - (683-104HC)
- (4) Black Side Outlet Tee - (681-604HC)
- (4) Black Standard Railing Flanges - (683-204HC)
- (2) Black 12" Non Threaded Pipe - (584-120PE30HC)
- (4) Black 18" Non Threaded Pipe - (584-180PE30HC)
- (2) Black 36" Non Threaded Pipe - (584-360PE30HC)
Other Supplies:
- (16) Wood Screws
- (1) 40" x 18" Wood Piece - Top
- (1) 36" x 14" Wood Piece - Middle
Tools:
- Allen Wrench - 6 Millimeter
- Drill
How To
Stage 1
Building Horizontal Support
- Start by building the middle shelf.
- The fitting used will be the Side Outlet Tee (681-604HC). The sides will use 12” pipe (584-120PE30HC) and the front and back will use 36” pipe (584-360PE30HC).
- Making a square, attach the pipes to the Side Outlet Tees (681-604HC) as shown in above image. Make sure the vertical holes will not be blocked then tighten set screws.
Steel•Tek Professional Tip
- Place a pipe in the vertical holes when sliding the other pipe in horizontally. This way you know the vertical holes will not be blocked.
Stage 2
Installing Flanges and Legs
- Install your Flanges (683-104HC).
- If you have any concerns with the pipes not matching up when the Flanges (683-104HC) are installed then here is a little tip. When lining up the Flanges (683-104HC), place the pipes for the legs in the flanges, slide the base built in Stage 1 onto the legs then mark the Flange (683-104HC) holes. By doing this you are guaranteeing everything will line up once the Flanges (683-104HC) are installed.
- Once the holes are marked remove the middle shelf base and the legs and pre-drill the holes.
- Once the holes are pre-drilled, install the Flanges (683-104HC) using wood screws.
- Slide the 18" pipe (584-180PE30HC) legs in the Flanges (683-104HC) and tighten set screws.
Stage 3
Installing Horizontal Base
- Slide the middle shelf onto the legs until centered or placed at desired height then tighten set screws.
- Cap the bottom of the legs off with Flanges then tighten set screws.
Stage 4
Placing Middle Wood Piece
- Place the wood piece on the middle shelf.
- Since this is specifically made for shoes it is not necessary to secure the wood to the pipe.
- If there are concerns then you can use Offset Flanges (689-904HC) on each middle shelf pipe to secure the wood.