- Products
-
Projects
- Decorative Shelf
- Sofa Table
- Entryway Shoe Rack
- Stair Railing
- Bicycle Exercise Stand
- Coding Table
- Train Table
- Buffet Table
- Target Range
- Candle Holder
- Decorative Bench
- Outside Bench
- Napkin Holder
- Step Stool
- Fence Wood Rack
- Accessory Holder
- Plant Hanger
- Mail Slot Table
- Coffee Cart
- Bench
- Kitchen Island Rack
- Full Bed
- Gym Hooks
- TV Console
- Bar Top
- Wall Mounted Barbell Rack
- Swivel Table
- Mailbox
- TV Stand
- Console Shelf
- Full Bed
- Towel and Toilet Paper Rack
- Garage Shelf
- Coat Rack
- Stool
- Garage Workbench
- Living Room Table
- Outdoor Railing
- Bookshelf
- Wall Shelf
- Small Shelf
- Entryway Coat Rack
- Decorative Serving Cart
- Serving Station
- Serving Cart
- Corner Desk
- Conference Room Table
- Side Table
- Hallway Table
- Lamp
- Lamps
- Coffee Table
- Decorative Coffee Table
- Worktable
- Blog
- About
- Contact
Products
Projects
Blog
About
Contact
Decorative Shelf
Build this Decorative Shelf and make your home or office pop!
Skill Level
Estimated Cost
Estimated Time
Tools & Materials
SteelTek Supplies (3/8"):
- (4) Flange - (683-102HC)
- (4) Elbow - (682-502HC)
- (8) Single Socket Tee - (680-102HC)
- (20) Side Outlet Tee - (681-602HC)
- (30) Offset Flange (689-902HC)
- (4) 72" Non Threaded Pipe
- (14) 36" Non Threaded Pipe
- (12) 12" Non Threaded Pipe
Other Supplies:
- (30) Wood Screws
- (5) 40" x 12" Wood Pieces
Tools:
- Allen Wrench - 5 Millimeter
- Drill
How To
Stage 1
Building Legs
- Take a 12” pipe and attach an Elbow (682-502HC) to each side of 12” pipe. Make sure the elbows are facing the same direction and tighten set screws
- Slide a 72” pipe into each open end of Elbow (682-502HC) then tighten set screws.
- Do this step 2 times.
Stage 2
Building Shelf Supports and Back Supports
- Take (2) 36” pipes and slide (2) Offset Flanges (689-902HC) onto each pipe. Cap each side of 36” pipe with a Side Outlet Tee (681-602HC). Make sure the Side Outlet Tees (681-602HC) are facing the same direction and the vertical hole is not being blocked then tighten set screws.
- Take (2) 12” pipes and slide (1) Offset Flange (689-902HC) onto the 12” pipe. Slide the 12” pipe into the open ends of the Side Outlet Tees (681-602HC) attached to the 36” pipe. Complete these step 5 times.
- Take a 36” pipe and attach a Single Socket Tee (680-102HC) to each side of 36” pipe. Make sure the vertical holes are not blocked in the Single Socket Tees (680-102HC) then tighten set screws. Complete this step 4 times
Stage 3
Installing Shelf and Back Supports
- Slide the shelves and back support per instructions.
- Shelf Base, Back Support, Shelf Base, Back Support, Shelf Base, Back Support, Shelf Base, Back Support, Shelf Base.
- Spread these out evenly then tighten set screws.
Stage 4
Attaching Flanges and Installing Wood Shelves
- Cap the bottom off with Flanges (683-102HC) then tighten set screws.
- Attach the wood pieces using wood screws.
- Start from the top and go up and through the screw holes of the Offset Flanges (689-902HC). Do this slowly as not to crack the wood pieces.
Stage 5
Finish