- Products
-
Projects
- Boat Seat
- Boat Motor Mount
- Decorative Bookshelf
- Moving Work Station
- Loft Bed Railing
- Cabinet
- Kitchen Island
- Lofted Bed Accessories
- Kitchen Storage Shelf
- Closet System
- Patio Chair
- Patio Table
- Dolly
- Projector Screen
- Sign Frame
- Patio Frame
- Bird House
- Horse Shoes
- Dog Bowl
- Hanging Shelf
- Decorative Shelf
- Sofa Table
- Entryway Shoe Rack
- Stair Railing
- Bicycle Exercise Stand
- Coding Table
- Train Table
- Buffet Table
- Target Range
- Candle Holder
- Decorative Bench
- Outside Bench
- Napkin Holder
- Step Stool
- Fence Wood Rack
- Accessory Holder
- Plant Hanger
- Mail Slot Table
- Coffee Cart
- Bench
- Kitchen Island Rack
- Full Bed
- Gym Hooks
- TV Console
- Bar Top
- Wall Mounted Barbell Rack
- Swivel Table
- Mailbox
- TV Stand
- Console Shelf
- Full Bed
- Towel and Toilet Paper Rack
- Garage Shelf
- Coat Rack
- Stool
- Garage Workbench
- Living Room Table
- Outdoor Railing
- Bookshelf
- Wall Shelf
- Small Shelf
- Entryway Coat Rack
- Decorative Serving Cart
- Serving Station
- Serving Cart
- Corner Desk
- Conference Room Table
- Side Table
- Hallway Table
- Lamp
- Lamps
- Coffee Table
- Decorative Coffee Table
- Worktable
- Blog
- About
- Contact
Products
Projects
Blog
About
Contact
Corner Desk
Great for any office! Utilizes space and great storage!
Skill Level
Estimated Cost
Estimated Time
Tools & Materials
SteelTek Supplies (3/4"):
- (10) Flange: (673-104HC)
- (3) Side Outlet Tee: (671-604HC)
- (2) Single Socket Tee: (670-104HC)
- (2) Single Swivel Socket: (677-304HC)
- (6) 28" Non-Threaded Pipe
- (2) 10' Non-Threaded Pipe (Cut to x2 47" and x2 13")
Other Supplies:
- (1) Desk Top
- (40) Wood Screws
- Stud Guards
Tools::
- (1) Allen Wrench - 6 Millimeters
- (1) Drill
How To
Stage 1
Installing Flanges
- Start by lining up two Flanges on each side of the bottom of the table and one Flange in the back middle (as shown in picture).
- Use your support pipe to help measure the length between each leg
- Mark holes, pre-drill then Install flanges into pre-drilled holes, with wood screws.
Steel•Tek Professional Tip
- When creating the wood top for the table we used stud guards to connect the pieces of wood together which is displayed in the second and third pictures.
Stage 2
Attaching Legs
- Slide the 28" pipes, which will be the legs, into each of the Flanges installed on the bottom of your table.
- Tighten set screws.
Stage 3
Building the Base
- Take one Side Outlet Tee and attach two 47" pipes onto each side of fitting (as shown in picture). Make sure not to slide the pipe too far in the fitting as not to block the hole for the vertical pipe (Legs).
- Slide top part of Single Swivel Socket onto each open end of 47" vertical pipe.
- Attach 28" pipe in bottom of both Single Swivel Sockets and tighten set screws.
- Attach Side Outlet Tee to open ends of each 47" pipe
- Slide 13" pipes into open end of each Side Outlet Tee and tighten set screw.
- Last, attach bottom of Single Socket Tee to open end of 13" pipe. Tighten set screw.
Steel•Tek Professional Tip
- Again, make sure that all vertical holes in the fittings are not being blocked so the legs slide through.
Stage 4
Attaching Base to Legs
- Take the base built in Stage 3 and slide from the bottom of the legs until at desired height then tighten all set screw.
- Lastly, slide the bottom of legs into Flanges and tighten set screws.
Steel•Tek Professional Tip
- Its is probably best to use a level to make sure that the base is nice and straight.