- Products
-
Projects
- Moving Work Station
- Loft Bed Railing
- Cabinet
- Kitchen Island
- Lofted Bed Accessories
- Kitchen Storage Shelf
- Closet System
- Patio Chair
- Patio Table
- Dolly
- Projector Screen
- Sign Frame
- Patio Frame
- Bird House
- Horse Shoes
- Dog Bowl
- Hanging Shelf
- Decorative Shelf
- Sofa Table
- Entryway Shoe Rack
- Stair Railing
- Bicycle Exercise Stand
- Coding Table
- Train Table
- Buffet Table
- Target Range
- Candle Holder
- Decorative Bench
- Outside Bench
- Napkin Holder
- Step Stool
- Fence Wood Rack
- Accessory Holder
- Plant Hanger
- Mail Slot Table
- Coffee Cart
- Bench
- Kitchen Island Rack
- Full Bed
- Gym Hooks
- TV Console
- Bar Top
- Wall Mounted Barbell Rack
- Swivel Table
- Mailbox
- TV Stand
- Console Shelf
- Full Bed
- Towel and Toilet Paper Rack
- Garage Shelf
- Coat Rack
- Stool
- Garage Workbench
- Living Room Table
- Outdoor Railing
- Bookshelf
- Wall Shelf
- Small Shelf
- Entryway Coat Rack
- Decorative Serving Cart
- Serving Station
- Serving Cart
- Corner Desk
- Conference Room Table
- Side Table
- Hallway Table
- Lamp
- Lamps
- Coffee Table
- Decorative Coffee Table
- Worktable
- Blog
- About
- Contact
Products
Projects
Blog
About
Contact
Coding Table
Code from home with SteelTek!
Skill Level
Estimated Cost
Estimated Time
Tools & Materials
SteelTek Supplies (3/4"):
- (6) Single Socket Tee - (670-104HC)
- (4) Side Outlet Tee - (671-604HC)
- (4) Flange - (673-104HC)
- (4) Elbow - (672-504HC)
- (6) Double Tab Offset Flange - (679-804HC)
- (2) Three Socket Tee - (670-404HC)
- (4) 2.875" Non Threaded Pipe
- (3) 18" Non Threaded Pipe
- (2) 36" Non Threaded Pipe
- (4) 24" Non Threaded Pipe
- (3) 72" Non Threaded Pipe
Other Supplies:
- (1) 96" x 30" Wood Top
- (12) Wood Screws
Tools:
- Allen Wrench - 6 Millimeter
- Drill
How To
Stage 1
Building Supports
- Start by assembling the vertical supports.
- See above diagram for pipe sizes and the fittings that attach to them.
- Left and Right Legs: Take (2) 36” pipes and slide a Single Socket Tee (670-104HC) until centered then tighten set screws. Cap both sides off with Side Outlet Tees 670- (671-604HC) as shown in diagram then tighten set screws.
- Left and Right Supports: Take (2) 18” pipes and attach a Single Socket Tee (670-104HC) to one side and a Three Socket Tee (670-404HC) to the other then tighten set screws.
- Middle Support: Take (1) 18” pipe and attach a Single Socket Tee (670-104HC) to both sides then tighten set screws.
Steel•Tek Professional Tip
- It is important to note to not block the vertical holes of the fittings because the pipe will need to slide through.
Stage 2
Attaching Legs and Supports
- Take (3) 72” pipes and begin to attach the supports built in Stage 1 as shown in above diagram.
- Slide the right support onto the left of the bottom and middle 72” pipes.
- Slide the middle support onto the left of the bottom and middle 72” pipes.
- Slide the left support onto the lift side of the bottom and middle 72” pipes.
- Separate the supports by 17.0635” then tighten set screws.
- Slide two Double Table Offset Flanges (679-804HC) onto the top pipe.
- Cap the left side off with the left leg and the right side off with the right leg. Make sure the horizontal holes of the Side Outlet Tees (671-604HC) are not blocked then tighten set screws.
Stage 3
Attaching Cross Beams
- Build the feet first. Take (4) Elbows (672-504HC), (4) Flanges (673-104HC) and (4) 2.875” pipes and attach them according to above diagram. If done correctly, the pipe will be minimally seen.
- Take (2) 24” pipes and slide them into the top Side Outlet Tees (671-604HC) until centered then tighten set screws. Cap each side off with a Double Tab Offset Flange (679-804HC) then tighten set screws.
- Take (2) 24” pipes and slide them into the Side Outlet Tees (671-604HC) located on the bottom. Center the pipe then tighten set screws. Cap each side off with the feet you built in step one of stage 3.
Stage 4
Attaching Wood Top
- Attach your 96” x 30” wood piece to the Double Tab Offset Flanges (679-804HC) using wood screws.
Stage 5
Finish